Accesorios

Model	Code	Features
Standard cable FR	200063	This 5 pin cable is supplied standard with any /FR screwdriver. Length: 2,5 m.
Standard cable TA	250063/N	This 8 pin cable is supplied standard with any /TA torque & angle screwdriver. Length: 2,5 m.
Tool balancers TECBA1	010300	New tool balancers TECBA1, code no. 010300, allow screwdrivers to be positioned over the work station for comfortable operation. Models with higher capacity available on request.
ARMPV1 support arms	010500	ARMPV1 support arms, code 010500, consist of a vertical support on which a 180° pivoting arm is attached.
Double output connector DOCK01	020020	A double output connector is available for operators using two FAB or RAF screwdrivers in the same working area. One end is to be connected to the controller (cable included), the other end to the drivers. Screwdrivers not to be used at the same time
Double output connector DOCK02	020035	A double output connector is available for operators using two KBL..FR (not KBL..FR/CA nor KBL..FR/S) screwdrivers in the same working area. The screwdrivers can be used at the same time.
Double output connector DOCK02/S	020035/S	A double output connector is available for operators using two KBL..FR/S screwdrivers in the same working area. The screwdrivers can be used at the same time.
Double output connector DOCK04	020045	A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP in the same working area. The screwdrivers cannot be used at the same time.
Double output connector DOCK04/TA	020045/TA	A double output connector is available for operators using two PLUTO screwdrivers with EDU2AE/TOP/TA in the same working area. The screwdrivers cannot be used at the same time.
Extension ring KP05	234511/K	KP05, code 234511/K, is an extension ring to be used with Pluto inline drivers for easier clamping on reaction arms.
Angle Head FAB – ANG HD1	010100	When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. ANG HD1 is the cost effective alternative to ANG HD8. 1/4” hex – max torque 6 Nm
Angle Head RAF – ANG HD2	010120	When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. ANG HD2 is the cost effective alternative to ANG HD9. 1/4” hex – max torque 6 Nm
Angle Head FAB – ANG HD8	010143	When space is limited a right angle head can be easily attached to lever start FAB screwdrivers. Model ANGHD8, code 010143, is suitable to FAB series. 1/4” hex – max torque 6 Nm
Angle head RAF – ANG HD9	010144	When space is limited a right angle head can be easily attached to lever start RAF screwdrivers. Model ANGHD9, code 010144, is suitable to RAF series. 1/4” hex, coppia max 6 Nm
Socket tray for TOP unit	020042	When using a multiple torque system a socket tray can be a useful accessory for program selection. It’s very easy to use: the control unit automatically selects the correct preset program when a bit or socket is removed.
Switchbox for TOP unit	020033	A switch box can be a useful accessory for multiprogram selection. It’s very easy to use: each time a button is pushed, the control unit automatically selects the preset program.
KBL clutch cover	02002- 02002-/CA	Clutch cover for KBL. Code 020028 for KBL04-15FR; Code 020028/CA for KBL04-15FR/CA; Cod. 020029 for KBL30FR; Code 020029/CA for KBL30FR/CA.
Autocatcher	01011-	An Autocatcher allows the operator to to pick up and fasten stainless steel, brass, copper and plastic screws by using one hand! Sizes available: AC2.3 for M2 to M3, code 010113, AC3.5 for M3 to M5, code 010114.
ACE Screw Counter	02002-	The ACE screw counter is a process control system that monitors the fastening assembly process. It tracks, in real time, the fastening of each screw in an assembly, then notifies the result.
Telescopic Spindle	8003–	The Telescopic Spindle (axial compensator) is used in multi spindle applications to balance the screw tightening process and compensate depth difference across multiple fasteners.
Coloured Rings	2000–	Coloured rings are useful to distinguish and identify different screwdrivers at a glance. Available in different colours: Code 200085 – Blue Code 200086 – Red Code 200087 – Yellow Code 200088 – Green Code 200089 – Black
Barcode reader BRCR90	020050	The BRCR90 barcode reader allows the operator to instantly select the program previously set on the control unit. To be used with EDU2AE/TOP or EDU2AE/TOP/TA.
Serial Printer PRNTR1	020026	The PRINTR1 serial printer gives the possibility to instantly print the results of each tightened screw. It works with EDU2AE/TOP, EDU2AE/TOP/TA, EDU2AE/HPRO control units and K and Mini K../S torque testers.
Cable with strain relief	250063/H	The cable with spring is more resistant thanks to a longer connector and spring, which makes the cable up to 4 times more endurable. Perfectly compatible with any 5 pin (code 200063/H) or 8 pin (code 250063/H) screwdriver/control unit.
Ethernet Device	020075	Kolver Ethernet Device (code 020075) makes it possible to connect a PC to any EDU 2AE/TOP – TOP/E – TOP/TA via remote LAN connection.
Light stack	020080	The light stack allows better visibility of output signals. Made for any control unit with signals. Supplied standard with 2,5m cable and 10pin connector for CN1 (EDU2AE – EDU2AE/TOP). Wiring for other Kolver control units available on request.
Start / Reverse Pedals	020070	Start and reverse signals can now be activated using our new foot pedal. Supplied standard with 3,5 m cable and connector for any EDU2AE and EDU2AE/TOP unit.
A2 and A3 Suction Heads	010111/-	A suction head is the best way to handle non-magnetic screws (stainless steel, brass, plastic etc.). Available in two models: A2 for M2-M2,6 screws (code 010111/1) and A3 for M3-M4 screws (code 010111/2). A2 and A3 can be installed on any screwdriver
ASP HD Suction Heads	0101–	A Suction Head is the best way to handle non-magnetic screws (stainless steel, brass, plastic etc). Available for NATO 15 (ASP HD6, code 010117), NATO50 (ASP HD7, code 010118), MITO15 (ASP HD8, code 010119) and PLUTO3-15 (ASP HD9, code 010121).
RIV HD Bit Guides	01018x	Bit Guides are the best accessory to help long bits, wire thread insert and riveters keep the correct perpendicular position. For PLUTO and KBL screwdrivers.
Reduced Front Ring for PLUTO	234515	Inline PLUTO screwdrivers can be supplied with reduced front ring (code 234515). The new reduced front ring, code 234515, is also available as accessory/spare part and supplied with four M3x6 screws.
Support for angle head screwdrivers	010176	To be installed on vertical sufaces to quickly store RAF and PLUTO angle screwdrivers.
Universal pistol grip support	010175	To be installed on vertical surfaces to quickly store any Kolver pistol grip tool, including FAB, RAF, KBL, PLUTO and KDS models.
KDU Adapter kit with SW and CBS	010410	Connect your KDU control unit to this KDU Adapter and select up to 8 programs or sequences via SWBX88 Switchbox or CBS880 socket tray.
Table stand for KDU	010400	A table stand ensures quick access to cables when placing your KDU unit on a flat surface. It is the best option in case you’d like to keep your KDU controller right at hand.
Wall mount for KDU	010401	Wall mounts can be easily installed on any vertical surface and allow KDU controllers to tilt up/down and left/right – place your KDU unit anywhere and adjust its position to best suit your needs.
2.5 m Cable for K-Ducer	250064	Connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 2.5 m
5 m Cable for K-Ducer	250564	Connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 5 m
2.5 m Cable for K-Ducer, with spring	250064/H	Heavy duty connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 2.5 m
5 m Cable for K-Ducer, with spring	250564/H	Heavy duty connection cable between KDS screwdrivers and KDU controllers (M16, 10 pin). Length: 5 m
Double output connector DOCK05	020046	A double output connector is available for operators using two KDS screwdrivers with one KDU controller in the same working area. The screwdrivers cannot be used at the same time.
UR-Mount	010695/UR	Tool holder for screwdrivers up to ∅37mm, to be attached to Universal Robots® robotic arm. Code no. 010695/UR for PLUTO3, 6, 10, 15CA and CA/FN2 \| Code no.010695/URM for MITO \| Code no. 010695/URN for any tool ∅19-37mm
Link cable kit from KDU to UR robot	020078	Ready-made interface to connect KDU Controllers to UR Robot.

Productos relacionados